Cure Window Mapping: Validating 365, 385, 395 and 405 nm on a Production Line
Build a reusable cure-window record for your line. Compare four LED wavelengths, set irradiance and dose conventions, and track lamp decay over time.
Once a line has moved to LED curing, the wavelength is fixed. What is not fixed is the dose the formulation actually receives, because lamps age, optics collect dust, and substrates and film thickness change. Without a record of how the line behaved when it was known to be good, every cure problem becomes an investigation from scratch. A cure-window map is that record: a repeat set of measurements at 365, 385, 395 and 405 nm that links lamp output to a few decisive film properties. This article explains how to build the map, which measurement conventions must be fixed first, how to track lamp decay, and how to reuse the record when a formulation or a lamp changes. No recommended energy values are given; the baseline belongs to your own line.
1. Why a reusable window record matters
A cure specification written for a mercury lamp does not transfer cleanly to an LED source. Mercury lamps emit across a broad spectrum, while LEDs deliver narrow bands, so the same nominal energy can produce very different cure in a photoinitiator system tuned to one wavelength. The first job of the window record is to make that relationship visible for your formulation.
The second job is to capture time. Output falls as a lamp ages, but the mechanism differs between technologies and between installations: lamp bodies discolour, drivers drift, lenses and reflectors collect residue, and cooling conditions change the output of an LED array. A recorded baseline turns a vague impression that the line is weaker into a measurable comparison.
2. The four-wavelength test matrix
Test the same formulation, substrate and film thickness at each available wavelength, and record the same small set of outcomes. Surface cure, through cure and adhesion are usually enough to separate the wavelengths; hardness or solvent rub can be added where the application demands it. Keep the coating procedure identical across the matrix so wavelength is the only deliberate variable.
Thick and pigmented systems are the most sensitive. Longer wavelengths generally penetrate further into a coloured layer, while shorter wavelengths are often absorbed near the surface, so a change from one band to another can shift the balance between a tack-free surface and a fully cured base. The matrix is where that trade-off is captured rather than guessed.
| Wavelength | Surface cure observation | Through-cure observation | Adhesion observation | Where it tends to help |
|---|---|---|---|---|
| 365 nm | Record surface state at fixed settings | Record through-cure result | Record named adhesion test result | Surface-oriented initiation in many systems |
| 385 nm | Record surface state at fixed settings | Record through-cure result | Record named adhesion test result | A middle option between surface and penetration |
| 395 nm | Record surface state at fixed settings | Record through-cure result | Record named adhesion test result | Common LED band for pigmented and thicker layers |
| 405 nm | Record surface state at fixed settings | Record through-cure result | Record named adhesion test result | Greater penetration in some coloured systems |
Empty matrix template. Fill each cell with your own measured result at fixed film thickness, substrate and line settings.
3. Measuring irradiance, dose and line speed
Irradiance and dose are not interchangeable. Irradiance, measured in milliwatts per square centimetre, describes how much radiant power arrives at a point; dose, in millijoules per square centimetre, is irradiance integrated over exposure time. Line speed connects the two by determining how long any point under the lamp is exposed.
Agree the measurement convention before collecting data. Use a radiometer suited to the wavelength being measured, fix the sensor position and orientation, and state whether the reading is peak irradiance or an integrated value. Record the distance from lamp to substrate, the number of passes and the direction of travel. A dose figure without those details is not repeatable.
| Measurement | Convention to fix | Why it matters | When to re-measure |
|---|---|---|---|
| Peak irradiance | Radiometer model, sensor position and distance | Determines the intensity arriving at the film | At the fixed cadence and after cleaning |
| Integrated dose | Exposure time and number of passes | Links lamp output to line speed | Whenever line speed or pass count changes |
| Lamp-to-substrate distance | Fixed fixture and recorded value | Small changes alter irradiance significantly | After any fixture or maintenance work |
| Cooling condition | Airflow or cooling setting recorded | LED output depends on operating temperature | When output drifts without an optical cause |
| Baseline ratio | Current reading divided by stored baseline | Shows decay independent of absolute units | Every session |
Measurement conventions must match your equipment. No numeric limits are prescribed here.
4. Lamp decay and re-test rhythm
Set a fixed cadence for re-measuring output and tie it to production hours rather than to the calendar alone. At each check, measure the same wavelengths at the same position and compare with the stored baseline. The useful quantity is the ratio to baseline under identical conditions, not an absolute number borrowed from another machine.
Define in advance what happens when output falls below an agreed fraction of baseline: clean the optics and re-measure, check cooling and driver conditions, then plan lamp replacement if recovery is not possible. The threshold is a site decision based on when film properties begin to drift, which is exactly what the window map records.
5. The record template
A good record is boring and complete. It lets a colleague reproduce the measurement, and it makes the next deviation obvious. The table lists the columns worth keeping; a spreadsheet with one row per measurement session is usually sufficient.
6. Reusing the map after a change
When a formulation changes, keep the lamp data and repeat only the film-property matrix. When a lamp or an optic changes, keep the formulation data and re-measure the output profile first, then repeat the matrix to confirm the old relationship still holds. Separating the two kinds of change prevents a lamp event from being misdiagnosed as a resin problem.
The same discipline helps when a complaint arrives from a customer. If the line record shows output within its normal band and the film results match the stored matrix, attention can move to substrate, pretreatment or print variables. If output has drifted, the cure record shortens the investigation considerably.
| Trigger | What changed | Action | Record to keep |
|---|---|---|---|
| New formulation | Resin or initiator package changed | Repeat the four-wavelength film matrix | New matrix beside the old one |
| Lamp replacement | Output device or driver changed | Re-measure output profile, then repeat matrix | Before and after output readings |
| Optics cleaned | Reflectors or lenses serviced | Re-measure output at the fixed points | Cleaning date and restored ratio |
| New substrate | Different colour, reflectance or thickness | Run the matrix on the new substrate | Substrate details with the result |
| Output below threshold | Ratio to baseline fell below the agreed limit | Clean, check cooling, then plan replacement | Trend of ratios over time |
Re-run triggers. The threshold itself is a site decision derived from when film properties begin to drift.
Frequently asked questions
1. Can I compare dose readings from two different radiometers?
Only with caution. Sensor response and geometry differ, so a reading is meaningful mainly against a baseline taken with the same instrument in the same position. If you change meters, take an overlapping set of measurements before replacing the old record.
2. Why does the same dose give different cure on two substrates?
Because colour, reflectance, thickness and heat capacity change the light that reaches the resin and how the film behaves afterwards. Keep the substrate and film thickness fixed in the matrix, then test each new substrate as a separate row.
3. How often should lamp output be checked?
Tie the cadence to production hours and to how close the process runs to its cure limit. A line with little margin needs shorter intervals; a stable process may need fewer. Use the point where film properties start to drift as the real trigger.
4. Does a higher wavelength always cure thicker films better?
Not universally. Penetration depends on the photoinitiator absorption and the composition of the coating, not on wavelength alone. The four-wavelength matrix exists to answer that question for your own formulation rather than to assume it.
Explore related Bawo-Chem materials
- Photoinitiators — absorption across the common LED wavelength bands.
- UV solutions by application — how cure demands differ across applications.
- Oxygen inhibition explained — why surface cure needs its own check.
- Full acrylates — acrylate systems used across curing processes.
- All product platforms — an overview of the available material families.
Mapping a cure window?
Share your lamp wavelengths, film thickness and substrate. Our team can discuss which material families to screen in a first comparison.
Talk to a formulation engineer