How to Read a UV Resin TDS: 12 Specifications That Actually Change a Formulation
A UV resin TDS is a process forecast, not a list of numbers. See 12 specifications that change viscosity, cure, adhesion and batch acceptance before sampling.
A technical data sheet is usually the first document requested and the least carefully read. In a UV curing project it tends to arrive as an attachment to a quotation, gets filed, and is only opened again when a trial goes wrong. That is a waste of a useful document. A well-built TDS is not a list of numbers about a liquid; it is a forecast of how that liquid will behave on a particular line, at a particular film build, under a particular lamp. This article reorganises the twelve fields that matter into the decisions they actually control, and ends with a short incoming-goods routine that catches most batch problems before they reach the coater.
1. Why one data sheet produces two different decisions
A formulator opens a TDS looking for viscosity, functionality and cure response, because those decide whether the resin can be pumped, applied and cured at the required line speed. A buyer opens the same page looking for shelf life, packaging, density and whether the certificate of analysis will accompany each delivery. Both readings are correct, and both are incomplete. What usually goes unread is the small print that makes every number meaningful: the temperature at which viscosity was measured, the film build and substrate used for hardness, the lamp and dose behind a cure-speed claim, and whether a figure is a guaranteed specification limit or a typical value.
The cost of that gap is familiar. A sample performs well in the laboratory and the production batch behaves differently. A purchasing team approves an equivalent grade on the strength of matching viscosity, then discovers the pigment wetting or adhesion has moved. A line is re-qualified for a new lamp, and nobody notices that the original data was generated under a different spectral output. In each case the resin may be entirely within specification — the specification was simply never tied to the process.
- Conditions are separated from values. A figure quoted without its test method is a label, not a measurement you can reproduce.
- Typical values are treated as limits. A TDS often mixes guaranteed ranges with indicative ones; only the CoA states what a specific batch actually measured.
- Liquid properties are read as film properties. Viscosity and colour describe the resin in the drum. Hardness, shrinkage and adhesion describe the cured film under stated conditions, and cannot be inferred from them.
The practical fix is to assign an owner and a check to each field, so that the formulator, the process engineer and the buyer are all reading the same column of the same sheet.
2. The twelve fields, sorted by what they control
Rather than reading top to bottom, group the fields into four questions: how the liquid handles, how it polymerises, what the cured film does, and whether the next drum will match this one. The same twelve appear on most acrylate and oligomer data sheets, though the notation varies by supplier.
| Field | How it is normally stated | What it changes in the process | Who should own the check |
|---|---|---|---|
| 1. Viscosity | mPa·s at a stated temperature, with the instrument and spindle | Pumping, coating weight, levelling and jetting reliability | Process engineer |
| 2. Functionality | Number of acrylate groups per molecule, often nominal | Crosslink density, shrinkage, and the hardness-versus-flexibility balance | Formulator |
| 3. Acid value | mg KOH/g, with the titration method | Adhesion on metal, pigment wetting, storage stability and container compatibility | Formulator and QC |
| 4. Colour | APHA or Gardner scale, sometimes both | Appearance of clear coats and pale inks; baseline for detecting batch drift | QC |
| 5. Density | g/cm³ at a stated temperature | Weight-to-volume dosing, fill levels and freight calculations | Purchasing |
| 6. Non-volatile content | Percent solids, with the drying conditions used | Wet-to-dry film build, VOC accounting and shrinkage behaviour | Process engineer and EHS |
| 7. Oligomer backbone | Urethane, epoxy, polyester or pure acrylate family | Flexibility, hardness, chemical resistance and pigment wetting | Formulator |
| 8. Molecular weight | Number-average value, where disclosed | The trade-off between viscosity and functionality; migration considerations | Formulator |
| 9. Cure response | Dose or line speed under a stated lamp and film build | Required irradiance, lamp settings and achievable throughput | Process engineer |
| 10. Cured-film hardness | Pencil, Shore or pendulum value, with film build and substrate | Scratch and abrasion resistance, and the risk of brittleness | Formulator |
| 11. Shrinkage | Volumetric change, or a qualitative indication | Adhesion on difficult substrates and dimensional accuracy of printed parts | Formulator |
| 12. Shelf life and storage | Months, temperature range, container and light conditions | Stock rotation, age checks on arrival and re-test rules | Purchasing and warehouse |
Field definitions and standard units only. The values for a specific grade come from that supplier's own data sheet and the certificate of analysis for the delivered batch; no product values are assumed here.
3. Four fields that are routinely misread
Viscosity without a temperature is not a number. Acrylate viscosity falls sharply as the resin warms, so a value measured at one temperature says little about how the material will run at another. The spindle, rotation speed and instrument matter too. When comparing two grades, ask for both measurements under the same method, or run them side by side on your own viscometer at the temperature the line actually reaches.
Functionality is not cure speed. A higher count of acrylate groups raises potential crosslink density, but the speed at which a film becomes tack-free also depends on the photoinitiator package, delivered dose, oxygen inhibition at the surface and the depth of the film. Chasing functionality alone often buys throughput at the cost of shrinkage, brittleness and adhesion loss on plastics or metals.
Acid value is not only a water-based concern. In a 100 percent solids UV system it still influences wetting of pigments and fillers, adhesion to metal substrates, compatibility with packaging and long-term storage stability. Two grades with near-identical viscosity and functionality can behave differently in a pigmented ink purely because their acid values differ, which is one reason a viscosity-based substitution so often disappoints.
Colour is a baseline, not a yellowing prediction. An APHA or Gardner figure describes the liquid as delivered. How a cured film changes colour after exposure depends on the photoinitiator, the stabiliser package and the cure dose. Use the colour figure to detect batch-to-batch drift and to protect pale shades, then evaluate yellowing separately on a cured panel under a defined ageing or exposure condition.
4. TDS, COA and SDS: which document answers which question
Much of the friction between a supplier and a customer comes from asking one document to do another document's job. Keep the three separate and the division of labour becomes obvious.
| Document | What it describes | Use it to | It cannot tell you |
|---|---|---|---|
| Technical data sheet | The grade: typical properties, specification ranges and test conditions | Shortlist a material and design the first trial | What the drum in front of you actually measured |
| Certificate of analysis | One batch: measured results against the agreed limits | Accept or hold a delivery and build a drift record | Whether the grade is right for the application |
| Safety data sheet | Hazards, handling, storage, transport and regulatory classification | Set handling, PPE and storage rules; support market-specific reviews | Performance, cure behaviour or batch conformity |
For regulated uses such as food contact, an application-specific evidence pack is a separate request again; do not assume a TDS or an SDS covers it.
One practical rule follows from this. A CoA value that differs from the TDS is not automatically a defect, provided it sits inside the declared specification range and the test method is the same. What matters is whether the field is a guaranteed limit or a typical value, and whether repeated batches are drifting in one direction. A slow upward trend in viscosity or colour is worth raising long before a single result crosses a limit.
5. A five-minute incoming-goods check
Twelve fields are too many to check on every delivery. Five actions cover the ones that change the process most often, and none requires a full laboratory panel. Keep a retained sample and a cured reference panel from the approved batch; most questions then become a direct comparison rather than a debate about numbers.
| Step | Check | Method | Escalate when |
|---|---|---|---|
| 1 | Grade, batch number and CoA match the delivery note and drum label | Document and label comparison | Any mismatch, or a missing CoA |
| 2 | Viscosity at your own recorded temperature and spindle | Viscometer, same method every time | Outside the agreed tolerance or a visible trend |
| 3 | Colour and clarity against the retained sample | Side-by-side visual or APHA comparison | Visible drift, haze or sediment |
| 4 | Age, seal integrity and storage history | Shelf-life date and storage log | Past date, opened container or unrecorded storage |
| 5 | Small cure panel at production dose, film build and substrate | Tack-free check, through-cure and cross-hatch adhesion | Any difference from the retained reference panel |
Routine template. Set the tolerances with your supplier and record the lamp, dose and film build used for the reference panel.
6. Questions to send a supplier before the first sample
A short written brief saves more time than an extra round of samples. Phrase each question so the answer is a document, a measured value or a stated method rather than a general assurance.
- Which test method, temperature, spindle and rotation speed sit behind the viscosity figure?
- Is functionality a nominal value or a measured one, and what batch tolerance do you hold on it?
- Which colour scale is used, and what is the upper limit applied to deliveries?
- At what film build, substrate, lamp and dose were the hardness and cure-response values measured?
- What shelf life is declared, under which storage conditions, and what re-test is required after that date?
- Which TDS fields are guaranteed on the CoA, and which are typical values only?
- Do you retain samples from each batch, and how are formulation or feedstock changes communicated?
- Which of these twelve fields would move if the manufacturing site or raw material source changed?
Frequently asked questions
1. Are viscosity figures comparable between two suppliers?
Only when the temperature, instrument, spindle and rotation speed match. Acrylate viscosity is strongly temperature dependent, so two sheets quoting different conditions cannot be compared directly. Ask both suppliers for the full test method, or measure the two samples yourself at the temperature your line runs at.
2. Does higher functionality always mean a faster cure?
No. Functionality influences crosslink density, but tack-free speed also depends on the photoinitiator package, irradiance, delivered dose, surface oxygen inhibition and film thickness. Raising functionality can improve throughput while reducing adhesion and flexibility, so confirm it on a cured panel rather than on the data sheet alone.
3. Why does acid value matter in a 100 percent solids UV system?
Because acidity affects more than water compatibility. It influences pigment and filler wetting, adhesion to metal substrates, storage stability and container compatibility. Two grades matched on viscosity and functionality can still behave differently in a pigmented ink, which is why acid value belongs in the substitution checklist.
4. What should I do if a CoA value falls outside the TDS range?
Hold the batch and ask whether the figure is a guaranteed limit or a typical value, and which method was used. Compare the material against a retained sample and run a small cure panel before release. If the deviation is confirmed, agree a disposition and a change-notification step with the supplier rather than adjusting the line to absorb it.
Explore related Bawo-Chem materials
- Reactive monomers — where viscosity, functionality and shrinkage are set together.
- Epoxy acrylate oligomers — hardness and reactivity to read against adhesion data.
- Polyester acrylates — pigment wetting and flow behind colour and acid value.
- Urethane acrylate oligomers — flexibility and abrasion resistance in the cured film.
- UV solutions by application — how each process weights these twelve fields differently.
Need a second opinion on a data sheet?
Send the TDS, your application and the property that is giving you trouble. Our team can suggest which material families to sample and which checks to run first.
Talk to a formulation engineer