Low-Migration UV Inks: What Food Packaging Converters Should Ask a Resin Supplier
A compliance statement is not an evidence pack. See eight documents to request from a UV resin supplier for food packaging, and what to check in each.
For a converter printing food packaging, the question used to be whether a UV ink carried a low-migration claim. It is now whether the whole supply chain can produce the documents behind that claim. Brand owners increasingly ask for evidence rather than assurances, and the ink maker cannot build that evidence without its raw material suppliers. Oligomers, monomers, photoinitiators and additives all sit upstream of the finished print, so what a resin supplier can document determines what a converter can prove. This article sets out the current industry frameworks, the eight documents worth requesting before a first trial, and the questions that reveal whether an evidence pack is complete.
1. Why a compliance statement is no longer enough
European food-contact rules have always required that materials do not transfer constituents to food in amounts that endanger health or change the food, and that every link in the chain remains traceable. What has changed is the depth of proof expected in practice. Positive-list approaches in Switzerland and Germany, a revised industry charter on raw material selection, and recyclability requirements under the packaging regulation have turned compliance into a documented, continuously maintained process rather than a one-off certificate.
The table below is a working map of the frameworks commonly raised in converter audits. It is a summary of publicly reported industry positions, not legal advice: each has its own scope, transitional provisions and enforcement dates, and the applicable text for a specific market and date should be checked before any compliance decision is made.
| Framework | Region and timing | What it changes for the supply chain | What to request |
|---|---|---|---|
| Regulation (EC) 1935/2004 | EU framework, long-standing | Sets the no-transfer principle and traceability obligation for food-contact materials | A written position and batch-level traceability back to the resin |
| Regulation (EU) 10/2011 | EU, plastics layer | Defines migration testing protocols for plastic food-contact materials | Test conditions and whether resin data supports the construction |
| Swiss Ordinance on food-contact materials | Switzerland, 2026 | Positive-list logic for substances used on the non-food-contact side of packaging | Component-by-component mapping to the current authorised list |
| German Ink Ordinance | Germany, expected 2027 | Extends comparable listing expectations to printing inks | Evidence that current components are listed or otherwise justified |
| EuPIA Charter on raw material selection | Europe, first edition March 2026 | Replaces the earlier industry exclusion policy and adds a risk-based tier for hazardous substances | Current charter status for each component, not a general statement |
| Packaging and Packaging Waste Regulation | EU, phased towards 2030 and 2035 | Makes recyclability a design requirement, which affects ink and coating choices | De-inking or recyclability information where the pack design depends on it |
Industry frameworks reported in public sources as of 2026. Scope, versions and effective dates differ by market; verify against the official text and your own application before publishing or approving a pack.
One consequence is worth stating plainly. Several photoinitiators widely used for long-wavelength LED curing have been reclassified or placed on industry exclusion lists in recent years, and formulators have been moving to alternative packages. That is an industry-wide shift, not a property of any one supplier. What a converter should ask for is the current status of every component in the specific grade, with the supporting documents, rather than a blanket assurance that a formulation is compliant.
2. Where migration risk actually enters a UV formulation
Migration is not a property of the ink alone. It is the result of what is in the formulation, how completely it cures, and how the printed construction is stored and used. A resin supplier controls the first of these and can supply data on it; the rest belongs to the converter and the printer.
- Photoinitiator packages and their by-products. Cleavage products and unreacted residues are among the first substances examined in a migration study, which is why absorption behaviour and composition disclosure belong together.
- Unreacted monomer and oligomer. Low-molecular-weight species that do not enter the network remain mobile. Functionality, conversion and cure dose all influence how much is left.
- Pigments, additives and impurities. Stabiliser packages, adhesion promoters and trace impurities in raw materials can matter as much as the main resin, and need to appear in the composition statement.
- Incomplete cure. Insufficient dose, a mismatched wavelength, oxygen inhibition at the surface or an excessive film build all increase the fraction of unreacted material.
- Set-off during storage. In reel and stacked-sheet configurations, the printed surface can contact the reverse of the next layer before the pack is filled.
- Substrate and barrier performance. A functional barrier changes the exposure pathway, so test results generated on a different construction may not describe the finished pack.
This split is the reason an evidence pack has two halves: supplier documentation for the substances and batches, and converter validation for the process and the finished article. Neither substitutes for the other.
3. The eight documents to request from a resin supplier
Send the following list as one written request, before samples ship and before anyone commits to a production grade. It is deliberately phrased to produce documents and measured conditions rather than marketing claims. No migration limits or test values are assumed here; those depend on the final construction, contact conditions and the market in which the pack is sold.
| Document | What it establishes | What to check inside | A reason to pause |
|---|---|---|---|
| 1. Composition statement | Which substances are present and what role each plays | Identifiers, functional role, and whether impurities are addressed | A generic blend description with no identifiers |
| 2. Current safety data sheet | Classification, handling and storage for the grade as supplied | Revision date, classification, and consistency with the composition statement | An old revision or a classification that conflicts with other files |
| 3. Market-specific regulatory status | Whether components are acceptable where the pack will be sold | Named markets, the legal basis cited, and the assessment date | One global claim with no region or date |
| 4. Positive-list mapping | Where each component stands against the relevant authorised list | List version, component names and the mapping method used | Unmapped components or an out-of-date list version |
| 5. Migration or extractables test data | Measured behaviour under defined conditions | Method, simulant, temperature, time, ink laydown, cure dose and laboratory | Results presented with no test conditions |
| 6. Worst-case assumptions and intended use | How the data applies to your construction | Substrate, barrier, contact type, storage and set-off assumptions | Assumptions that do not resemble your pack |
| 7. Certificate of analysis and batch traceability | What the delivered batch actually contains | Batch number, measured values and a link back to the tested formulation | No batch link, or drift with no explanation |
| 8. Change-notification and phase-out policy | How you will learn about a formulation or status change | Notification window, version control and handling of discontinued substances | No written commitment to notify |
Checklist only. Which documents are required, and which values apply, depend on the final use, the substrate, the ink laydown and the market; confirm them with your own regulatory function.
4. How to read an evidence pack
A complete-looking folder can still be unusable. Five checks take minutes and catch most of the problems that surface later in a brand-owner audit.
- Check the dates first. A statement written against a superseded list or an old classification is a historical document, not evidence for a pack being printed now.
- Match the test conditions to your own line. Note the substrate, film build, cure dose, simulant, temperature and contact time. Data generated under milder conditions does not automatically transfer.
- Cross-read the documents against each other. Component names on the composition statement, the safety data sheet and the positive-list mapping should agree.
- Separate measured results from declarations. A supplier statement about status is not the same as a laboratory result, and both are needed in different places.
- Look for version control. Ask how you would know if a formulation, a manufacturing site or a raw material source changed after the pack was approved.
5. A question set to send before the first sample
Questions framed this way produce documents and conditions rather than assurances, and they give both sides a common definition of what an acceptable answer looks like.
| Question | Why it matters | A satisfactory answer |
|---|---|---|
| Which markets and which version of each list was this grade assessed against? | Status is market and version specific | Named markets, list versions and an assessment date |
| Can you provide the current status of every photoinitiator and additive in the package? | Minor components are often the ones that change classification | A component-level statement with supporting references |
| Under what ink laydown, substrate, cure dose and simulant were the migration tests run? | Determines whether the data can be applied to your construction | Full test conditions and the laboratory that produced them |
| Which values on the technical data sheet are guaranteed on the certificate of analysis? | Separates specification limits from typical values | A field-by-field list with batch tolerances |
| How are formulation changes, site changes and discontinued substances communicated? | An approved grade can quietly become a different one | A written notification window and version control process |
| Will the same grade and documentation be available for the production-scale run? | Prevents a successful trial being validated on a different material | Confirmation tied to a specific grade and batch record |
Template for a supplier brief. Add your own target market, substrate and contact conditions before sending.
6. What a supplier file cannot cover
Even a perfect evidence pack describes the material as supplied, not the print as produced. Conversion depends on dose, wavelength, film build and the atmosphere at the surface; a change in any of them can leave more unreacted material than the supplier's test assumed. Set-off during reel storage, the barrier performance of the chosen substrate, and the conditions under which the finished pack is filled and stored are all outside a resin supplier's control.
That is why converters should treat the supplier pack as an input to their own validation, not a substitute for it. Keep a retained sample and a printed reference panel from the approved trial, record the cure settings used, and re-run the checks whenever a batch, a lamp, a substrate or a formulation version changes. Good manufacturing practice documentation and traceability at the printing stage complete the chain that Article 17 of the EU framework asks for.
There is also a practical scheduling point. Regulatory status changes, and so do supplier formulations. An evidence pack should have an owner, a review date and a trigger for re-issue, otherwise the documents supporting a pack approved this year may quietly drift out of date while the pack itself stays in production.
Frequently asked questions
1. Does a low-migration grade guarantee a compliant finished package?
No. A grade can be formulated and documented for low-migration use, but the finished article also depends on cure dose, film build, substrate barrier, set-off during storage and the intended contact conditions. The supplier evidence covers the material; the converter still needs to validate the printed construction under its own conditions.
2. Which documents should arrive with every delivery?
At minimum a certificate of analysis with measured values, the batch number and a link to the tested formulation, plus confirmation that the current safety data sheet and regulatory status statement still apply. A drifting viscosity or colour value is also a prompt to check whether the composition has moved.
3. What if a supplier will not disclose full composition?
Confidential formulation details are often protected, but the gap needs to be closed rather than ignored. Common routes include a confidentiality agreement, disclosure to a named third party, or a component-level restricted-substance statement supported by independent testing. Record whichever route is used, and note the residual risk in your own assessment.
4. How often should the evidence pack be refreshed?
Whenever a regulation, a formulation, a manufacturing site, a raw material source or a target market changes, and as a scheduled review at least annually. Ask the supplier to date each statement and to notify you of changes, so a refresh is triggered by an event rather than discovered during an audit.
Explore related Bawo-Chem materials
- Photoinitiator platform — package composition and current status sit at the centre of any evidence pack.
- Full acrylates — oligomer families to evaluate where reactivity and film build are constrained.
- Reactive monomers — unreacted species are a recurring question in migration studies.
- Functional additives — stabilisers and adhesion promoters also belong in the composition statement.
- UV solutions by application — how exposure differs between ink, coating and adhesive processes.
Assembling a food-contact evidence pack?
Tell us your target market, substrate and ink laydown. Our team can suggest which material families to evaluate and which documents to request before the first trial.
Talk to a formulation engineer